PHLTD MDR Rail Series Switching Power Supply

MDR is a small multifunctional DC transformer that supports multiple output voltage specifications such as 5V, 12V, and 24V

Category:

PHLTD Rail Switch Power Supply MDR Series Wiring Diagram 85-264VAC 47HZ-63Hz (120VDC-370VDC)

PHLTD MDR-10, 20W product dimension diagram
PHLTD MDR-10W

PHLTD MDR Rail Series Switching Power Supply 10W20W Size 22.5x90x100mm Voltage Range/Frequency 85-264VAC 47Hz-63Hz (120VDC-370VDC)
PHLTD MDR-10, 20W Product Parameter Table
model MDR-10 MDR-20
DC Voltage 5V 12V 15V 24V 5V 12V 15V 24V
Rated current 2A 0.84A 0.67A 0.42A 3A 1.67A 1.34A 1A
rated power 10W 10W 10W 10W 15W 20W 20W 24W
Voltage accuracy ±5％ ±3％ ±3％ ±2％ ±2％ ±1％ ±1％ ±1％
Working current 0.33A/110VAC   0.21A/230VAC 0.55A/110VAC   0.35A/230VAC
output voltage 5V 12V 15V 24V
Ripple and noise ① ＜80mV ＜120mV ＜120mV ＜150mV
Voltage regulation range ±10％
Line Regulation ±1％
Load Regulation ±5％ ±3％ ±3％ ±2％
input Start, rise, hold time 1000ms、30ms、25ms ：110VAC 500ms、30ms、120ms ：220VAC
Voltage range/frequency 85-264VAC   47HZ-63Hz(120VDC-370VDC)
Efficiency (typical) ② ＞77％ ＞81％ ＞81％ ＞84％
Impulse current 110VAC  35A      220VAC  70A
Protective characteristics overload protection ≥ 105% -150% Type: Protection mode: Hiccup mode Automatic recovery after abnormal conditions are lifted
Overvoltage protection When the output voltage is greater than 135%, turn off the output and automatically recover after the abnormal conditions are resolved
environment Working temperature and humidity -20℃~+70℃;20%~90RH
Storage temperature and humidity -40℃~+85℃;10%-95RH
secure pressurization Input output: 3KVAC lasting for 1 minute
Isolation resistor Input output, input housing, output housing: 500VDC/100M Ω
other size 22.5*90*100mm
notes ① Ripple and noise measurement method: Use a 12 “twisted pair cable, with terminals connected in parallel with 0.1uF and 47uF capacitors, and measure at a bandwidth of 20MHz.
② Efficiency is tested at an input voltage of 230VAC, rated load, and an ambient temperature of 25 ℃.
Accuracy: including setting error, linear adjustment rate, and load adjustment rate.
Linear adjustment rate testing method: Test from low voltage to high voltage under rated load
Load adjustment rate testing method: from 0% to 100% of rated load.
The startup time is measured in a cold start state, and rapid and frequent shutdowns may increase the startup time,
When the operating altitude is above 2000 meters, the operating environment temperature needs to be reduced by 5 ℃/1000 meters
MDR-60W Product Dimensional Drawing
MDR-60W

PHLTD MDR Rail Series Switching Power Supply 40W60W Size 40x90x100mm Voltage Range/Frequency 85-264VAC 47Hz-63Hz (120VDC-370VDC)
MDR-60W Product Parameter Table
model MDR-40 MDR-60
DC Voltage 5V 12V 15V 24V 5V 12V 15V 24V
Rated current 8A 3.3A 2.67A 1.67A 12A 5A 4A 2.5A
rated power 40W 40W 40W 40W 60W 60W 60W 60W
Voltage accuracy ±2％ ±1％ ±1％ ±1％ ±2％ ±1％ ±1％ ±1％
Working current 1.1A/110VAC   0.7A/230VAC 1.8A/110VAC   1A/230VAC
output voltage 5V 12V 15V 24V
Ripple and noise ① ＜80mV ＜120mV ＜120mV ＜150mV
Voltage regulation range ±10％
Line Regulation ±1％
Load Regulation ±2％ ±1％ ±1％ ±1％
input Start, rise, hold time 1000ms、30ms、25ms ：110VAC 500ms、30ms、120ms ：220VAC
Voltage range/frequency 85-264VAC   47HZ-63Hz(120VDC-370VDC)
Efficiency (typical) ② ＞77％ ＞81％ ＞81％ ＞84％
Impulse current 110VAC  35A      220VAC  70A
Protective characteristics overload protection ≥ 105% -150% Type: Protection mode: Hiccup mode Automatic recovery after abnormal conditions are lifted
Overvoltage protection When the output voltage is greater than 135%, turn off the output and automatically recover after the abnormal conditions are resolved
environment pressurization Input output: 3KVAC lasting for 1 minute
Isolation resistor Input output, input housing, output housing: 500VDC/100M Ω
other size 40*90*100mm
notes ① Ripple and noise measurement method: Use a 12 “twisted pair cable, with terminals connected in parallel with 0.1uF and 47uF capacitors, and measure at a bandwidth of 20MHz.
② Efficiency is tested at an input voltage of 230VAC, rated load, and an ambient temperature of 25 ℃.
Accuracy: including setting error, linear adjustment rate, and load adjustment rate.
Linear adjustment rate testing method: Test from low voltage to high voltage under rated load
Load adjustment rate testing method: from 0% to 100% of rated load.
The startup time is measured in a cold start state, and rapid and frequent shutdowns may increase the startup time,
When the operating altitude is above 2000 meters, the operating environment temperature needs to be reduced by 5 ℃/1000 meters
MDR-100W Product Dimensional Drawing
MDR-100W

PHLTD MDR Rail Series Switching Power Supply 100W Size 56x110x90mm Voltage Range/Frequency 85-264VAC 47Hz-63Hz (120VDC-370VDC)
MDR-100W Product Parameter Table
model MDR-100
output DC Voltage 12V 24V 48V
Rated current 8.3A 4.1A 2A
rated power 100W 100W 100W
Ripple and noise ① 120mVp-p 150mVp-p 200mVp-p
Voltage regulation range ±10％
Voltage accuracy ±2.0％ ±1.0％
Line Regulation ＜±0.5％
Load Regulation ＜±1.5％ ＜±0.5％ ＜±0.5％
input Voltage range/frequency 85-264VAC    47Hz-63Hz(120VDC-370VDC
Efficiency (typical) ② ＞83％ ＞86％ ＞87％
Working current ＜1.3A 115VAC  ＜0.8A 230VAC
Impulse current 115VAC   30A，220VAC  60A
Start, rise, hold time 200ms、50ms、20ms ：220VAC
Protective characteristics overload protection ≥ 105% -150% Type: Constant current output+VO drops to undervoltage point Cut off output reset: Power on again
Short circuit protection +Vo drops to undervoltage point and closes output
environment Working temperature and humidity -10℃~+50℃;20%~90RH
Storage temperature and humidity -20℃~+85℃;10%-95RH
pressurization Input output: 1.5KVAC Input housing: 1.5KVAC
Output Housing: 0.5KVAC for 1 minute
Leakage current <5mA at 1.5KVAC input output
Leakage current <1mA when input-output 220VAC
Isolation resistor Input output, input housing, output housing: 500VDC/100M Ω
other size 56*110*90mm
notes ① Ripple and noise measurement method: Use a 12 “twisted pair cable, with terminals connected in parallel with 0.1uF and 47uF capacitors, and measure at a bandwidth of 20MHz.
② Efficiency is tested at an input voltage of 230VAC, rated load, and an ambient temperature of 25 ℃.
Accuracy: including setting error, linear adjustment rate, and load adjustment rate.
Linear adjustment rate testing method: Test from low voltage to high voltage under rated load
Load adjustment rate testing method: from 0% to 100% of rated load.
The startup time is measured in a cold start state, and rapid and frequent shutdowns may increase the startup time,
When the operating altitude is above 2000 meters, the operating environment temperature needs to be reduced by 5 ℃/1000 meters

High efficiency: Equipped with advanced power conversion technology, it ensures that the power supply maintains high efficiency during the conversion process, reduces energy waste, and reduces equipment operating costs.
Low standby power consumption: The wattage consumption of idle standby is lower than the industry standard, reducing power consumption in standby mode, in line with the modern concept of energy conservation and environmental protection.

Reviews

There are no reviews yet.

Be the first to review “PHLTD MDR Rail Series Switching Power Supply”

Your email address will not be published. Required fields are marked *

Related products

Shopping Cart