PHLTD EDR Rail Series Switching Power Supply

PHLTD EDR track series switch power supply 48V 24V 12V DC 75/120/150W，Suitable for industrial automation, LED lighting, and communication equipment

Category:

PHLTD Rail Switch Power Supply EDR Series Wiring Diagram Voltage Range/Frequency 85-264VAC 47Hz-63Hz (120VDC-370VDC)

Dimensional diagram of EDR-75W guide rail series products
EDR-75W

PHLTD EDR Rail Series Switching Power Supply 75W Size 32x125x102mm Voltage Range/Frequency 85-264VAC 47Hz-63Hz (120VDC-370VDC)
EDR-75W Guide Rail Series Product Parameter Table
model EDR-75
output DC Voltage 12V 24V 48V
Rated current 6.3A 3.2A 1.6A
rated power 75W 75W 75W
Ripple and noise ① 80mVp-p 120mVp-p 150mVp-p
Voltage regulation range ±10％
Voltage accuracy ±2.0％ ±1.0％
Line Regulation ＜±0.5％
Load Regulation ＜±1.5％ ＜±0.5％ ＜±0.5％
input Voltage range/frequency 85-264VAC    47Hz-63Hz(120VDC-370VDC)
Efficiency (typical) ② ＞85％ ＞87％ ＞88％
Working current ＜1.45A/115VAC  ＜0.91A/230VAC
Impulse current 115VAC   25A，220VAC  50A
Start, rise, hold time 200ms、50ms、20ms ：220VAC
Protective characteristics overload protection ≥ 105% -150% Type: Constant current output+VO drops to undervoltage point Cut off output reset: Power on again
Short circuit protection +Vo drops to undervoltage point and closes output
environment Working temperature and humidity -10℃~+50℃;20%~90RH
Storage temperature and humidity -20℃~+85℃;10%-95RH
pressurization Input output: 1.5KVAC Input housing: 1.5KVAC
Output Housing: 0.5KVAC for 1 minute
Leakage current <5mA at 1.5KVAC input output
Leakage current <1mA when input-output 220VAC
Isolation resistor Input output, input housing, output housing: 500VDC/100M Ω
other size 32*125*102mm
notes ① Ripple and noise measurement method: Use a 12 “twisted pair cable, with terminals connected in parallel with 0.1uF and 47uF capacitors, and measure at a bandwidth of 20MHz.
② Efficiency is tested at an input voltage of 230VAC, rated load, and an ambient temperature of 25 ℃.
Accuracy: including setting error, linear adjustment rate, and load adjustment rate.
Linear adjustment rate testing method: Test from low voltage to high voltage under rated load
Load adjustment rate testing method: from 0% to 100% of rated load.
The startup time is measured in a cold start state, and rapid and frequent shutdowns may increase the startup time,
When the operating altitude is above 2000 meters, the operating environment temperature needs to be reduced by 5 ℃/1000 meters
Dimensional diagram of EDR-120W guide rail series products
EDR-120W

PHLTD EDR Rail Series Switching Power Supply 120W Size 40x113.5x125mm Voltage Range/Frequency 85-264VAC 47Hz-63Hz (120VDC-370VDC)
EDR-120W Guide Rail Series Product Parameter Table
model EDR-120
output DC Voltage 12V 24V 48V
Rated current 10A 5A 2.5A
rated power 120W 120W 120W
Ripple and noise ① 100mVp-p 120mVp-p 150mVp-p
Voltage regulation range ±10％
Voltage accuracy ±2.0％ ±1.0％
Line Regulation ＜±0.5％
Load Regulation ＜±1.5％ ＜±0.5％ ＜±0.5％
input Voltage range/frequency 85-264VAC    47Hz-63Hz(120VDC-370VDC)
Efficiency (typical) ② ＞85％ ＞87％ ＞88％
Working current ＜12A 115VAC  ＜7.8A 230VAC
Impulse current 115VAC   25A，220VAC  50A
Start, rise, hold time 200ms、50ms、20ms ：220VAC
Protective characteristics overload protection ≥ 105% -150% Type: Constant current output+VO drops to undervoltage point Cut off output reset: Power on again
Short circuit protection +Vo drops to undervoltage point and closes output
environment Working temperature and humidity -10℃~+50℃;20%~90RH
Storage temperature and humidity -20℃~+85℃;10%-95RH
pressurization Input output: 1.5KVAC Input housing: 1.5KVAC
Output Housing: 0.5KVAC for 1 minute
Leakage current <5mA at 1.5KVAC input output
Leakage current <1mA when input-output 220VAC
Isolation resistor Input output, input housing, output housing: 500VDC/100M Ω
other size 40*113.5*125mm
notes ① Ripple and noise measurement method: Use a 12 “twisted pair cable, with terminals connected in parallel with 0.1uF and 47uF capacitors, and measure at a bandwidth of 20MHz.
② Efficiency is tested at an input voltage of 230VAC, rated load, and an ambient temperature of 25 ℃.
Accuracy: including setting error, linear adjustment rate, and load adjustment rate.
Linear adjustment rate testing method: Test from low voltage to high voltage under rated load
Load adjustment rate testing method: from 0% to 100% of rated load.
The startup time is measured in a cold start state, and rapid and frequent shutdowns may increase the startup time,
When the operating altitude is above 2000 meters, the operating environment temperature needs to be reduced by 5 ℃/1000 meters
Dimensional diagram of EDR-150W guide rail series products
EDR-150W

PHLTD EDR Rail Series Switching Power Supply 150W Size 60x113.5x125mm Voltage Range/Frequency 90-264VAC (127VDC-370VDC)/47Hz-63Hz

EDR-150W Guide Rail Series Product Parameter Table
model EDR-150
output DC Voltage 24V 48V
Rated current 6.25A 3.2A
rated power 150W 150W
Ripple and noise ① 150mVp-p 150mVp-p
Voltage accuracy ±10％
Line Regulation ±1.0％
Load Regulation ±1.0％
Voltage adjustable range ±10％
input Voltage range/frequency 90-264VAC (127VDC-370VDC)/47Hz-63Hz
Efficiency (Typical) (Typ.) ② 85.50% 90%
AC current (Typ.) 2.6A 115VAC    1.7A /230VAC
Start, rise, hold time 1500ms、60ms/230VAC,3000ms、60ms/115VAC
Protective characteristics overload protection ≥ 105% -150% Type: Constant current output+VO drops to undervoltage point Cut off output reset: Power on again
Short circuit protection +VO drops to undervoltage point and closes output
environment Working temperature and humidity -10℃~+50℃;20%~90RH
Storage temperature and humidity -20℃~+85℃;10%-95RH
pressurization Input output: 1.5KVAC Input housing: 1.5KVAC
Output Housing: 0.5KVAC for 1 minute
Leakage current <5mA at 1.5KVAC input output
Leakage current <1mA when input-output 220VAC
Isolation resistor Input output, input housing, output housing: 500VDC/100M Ω
size 40*113.5*125mm
notes ① Ripple and noise measurement method: Use a 12 “twisted pair cable, with terminals connected in parallel with 0.1uF and 47uF capacitors, and measure at a bandwidth of 20MHz.
② Efficiency is tested at an input voltage of 230VAC, rated load, and an ambient temperature of 25 ℃.
Accuracy: including setting error, linear adjustment rate, and load adjustment rate.
Linear adjustment rate testing method: Test from low voltage to high voltage under rated load
Load adjustment rate testing method: from 0% to 100% of rated load.
The startup time is measured in a cold start state, and rapid and frequent shutdowns may increase the startup time,
When the operating altitude is above 2000 meters, the operating environment temperature needs to be reduced by 5 ℃/1000 meters

Reviews

There are no reviews yet.

Be the first to review “PHLTD EDR Rail Series Switching Power Supply”

Your email address will not be published. Required fields are marked *

Related products

Shopping Cart